Xanigo Marine Dock & Deck Cleaner - 1 Gallon

Xanigo Marine Dock & Deck Cleaner - 1 Gallon

Dock & Deck Cleaner - 1 Gallon

Keep the dock and deck looking great while reducing harmful chemical runoff!

The base structure for the Xanigo Marine Dock & Deck Cleaner formula is made from plants, which enables it to have 94% bio-content as certified by the USDA. This uses next-generation renewable biosurfactant technology, is regarded as readily biodegradable, and is high-performing with high efficacy. Does not contain: Palm Oil, 1, 4-Dioxane, Formaldehyde, Proposition 65 Chemicals, Sulfates, Sodium Hydroxide, Glycol Ethers, Phosphates, Phthalates, Parabens, and Ammonia

Instructions for Use:

• For docks and decks, Xanigo Marine recommends a 1:5 to 1:20 dilution rate to enable proper cleaning. 1 gallon of Dock and Deck Cleaner to 5 to 20 gallons of water, depending on the job. This dilution ratio will provide effective cleaning power for composites, wood, and concrete
• Use a proper deck and dock brush with a minimum 2" bristle. The stiffness of the bristle should be tested on the dock users are trying to clean to determine which is the most effective
• For tough stains like blood, set-in bird drippings, or oils/greases, pour full strength into a spray bottle and spray the spots before scrubbing. After scrubbing the deck or dock, rinse with fresh water

Specifications:

• Bottle Size: 1 gallon

The Complete Process to Treat and Prevent Mold & Mildew on Vinyl Boat Seats

STEP 1: Remove Mold & Mildew with Xanigo Marine's Mold & Mildew Stain Remover

Xanigo Marin’s Mold & Mildew Stain Remover is a very effective way to remove mold and mildew. Being a harsh chemical, it should only be used once to remove the mold, and then the preventer should be applied to prevent the mold from coming back. Liberally apply the Mold & Mildew Stain Remover to the seats. Let it sit for 60-90 seconds but do not let it dry. An additional solution may need to be applied— keep it wet. Agitate in a circular motion with a brush to remove the mold from the pores. Rinse thoroughly with clean water.

STEP 2: Neutralize the Remover

After rinsing the remover off with fresh water, it's important to make sure any leftover remover is neutralized so it doesn't dry out vinyl or impact stitching. Spray the Waterless Wash onto the seats and wipe it in with a microfiber cloth to neutralize the chemicals in the remover.

STEP 3: Prevent Mold & Mildew with Xanigo Marine's Mold & Mildew Preventer

With just one application, a boat will be protected against mold and mildew for up to 90 days. The preventer creates a covalent bond with the surface on which it is applied. Users can apply this to almost any marine surface, including vinyl seats, life jackets, canvas, ropes, compartments, live wells, bilges, patio furniture, and other areas of high moisture.

Spray the Mold & Mildew Preventer onto a clean, dry surface and spread it evenly with a microfiber cloth. Remember to spread, not wipe off.

STEP 4: Maintain Seats with Xanigo Marine's Waterless Wash

Keep the boat clean between mold prevention applications without the use of harsh chemicals or wasting water. Spray the Waterless Wash onto the seats, let it sit for 15-20 seconds, and wipe it off with a microfiber cloth. Remove sunscreen (a major food source for mold) and leave a refreshing smell without impacting the protective layer created by the mold & mildew preventer.

Also, a great way to shine up a gel coat quickly!